The DigiMaster PRO (plus)
Dual channel DATA and CAT interface

Unleash the FULL power of Ham Radio Deluxe!
and other CAT and DATA software inc MixW etc.

Extremely popular, this interface has become our best selling interface by far !

Supports ALL data modes psk, rtty, etc, afsk and fsk with built in CAT interface.
Note that this interface can also be used with the "Y4" cable (available separately) which connects CAT via the FT857's and FT897's mic socket, so allowing FT857 and FT897users to continue using the CAT/LINEAR/TUNER socket for your ATU or other equpment.

Hi performance USB DATA and CAT interface.
All you need together in the one interface. Performance second to none, with professional quality isolating transformers in both RX and TX lines. Giving cleaner and clearer RX and TX signals, with no risk of receiving or worse, transmitting any "hum". Low power consumption makes it ideal for laptops as well as desktop.
For use with ALL AFSK and FSK DATA software including, HRD, DM780, MixW, DigiPan, N1MM, WSJT, etc.
Unleash the full power of programs like the Ham Radio Deluxe suite and MixW etc.

Because its dual channel, you can use your favourite CAT software at the same time as your favourite DATA mode software, eg, HRD CAT software and DigiPan PSK software (just one example).

Sturdy aluminum case, approx. case size of 80mm wide, 45mm high, 120mm deep.
On/off switch and red/green led for RX/TX.
Front panel TX and RX drive level adjustment.
The channel interface based on FTDI's popular 2232 USB chip, gives the interface 2 comports. The first comport gives you control over the interfaces PTT, CW, and TXD (fsk standard polarity) lines. The second comport being used exclusively for the CAT interface section. As the 2 comports are fully independent of each other, this gives you the ability to use whatever DATA mode software you wish to use, whilst at the same time, you to use whatever CAT software you wish to use, (provided that the CAT software you intend to use will support your radio of course).
Leads to PC are approx 1.8m length and leads from interface to radio are approx 0.8m length.
The CAT interface section is a plug in module that is available in 3 versions;
[1] CM1 - TTL CAT. (plus supports Y4 cable for CAT via mic on FT857 and FT897).
For all Icom the CIV radios and also the Yaesu radios that use a CAT interface, including many of the older Yaesu radios using either 6 pin din, 6 pin mini din, 8 pin mini din.
The CM1 also supports radio programming and has the same functionality as the DigiMaster MultiFace and so any MultiFace lead can also be used with the CM1 module.
[2] CM2 - Inverted TTL for the older Kenwoods TS450(s) and TS850(s) Esc that use the 6 pin din socket..
[3] CM3 - RS232 for those radios that use a serial cable.
The CW lead, USB and audio leads are supplied as standard.
The AFSK lead to the radio is included as per your selection of radio (below), wherever possible, (most Icom and Kenwood radios) the afsk lead will also be wired for FSK. However, many Yaesu radios need a separate FSK cable which is available as an extra optional extra.
The CW lead is fitted with a standard 3.5mm jack. If you radio needs a 1/4" CW jack then you will need an adapter.

If your radio is not in the list you will need to purchase the interface and its data and cat cables separately, or eMail us and we will either add your radio to the list or offer you a quote. (Quotes are valid for 7 days).

To utilize FSK your radio needs to support FSK (RTTY) and some radios (mainly Yaesu with 4 pin RTTY socket and several others inc the TS480 / TS950) may require a second / special FSK lead (purchased separately here) to operate FSK.